iPAQ H5100 Series Firmware Update WM2003 v1.00.11 (Official)

iPAQ H5100 Series Firmware Update WM2003 v1.00.11 (Official)

Requirements : iPAQ H5100 Series

Overview : This SoftPaq contains an "execute in place" (XIP) Cab file that replaces the "Miscellaneous OEM" region of the ROM Image for the listed handheld model. This is a permanent update to the flash ROM.

Installation Instructions :
1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Establish an Activesync connection between the iPAQ Pocket PC and
host PC using either a USB or Serial connection.

3. Execute the downloaded file and follow the on-screen instructions.

INSTALLATION NOTES:
1. If the Regional Settings are changed to any language other than the
default language of the handheld, the Firmware update will not
complete and generate the following error message: "This update is
language specific. Please visit the HP website to verify that you
have downloaded the correct update.

2. IMPORTANT: Please observe the following restrictions:
- Do not enable the handheld password feature during the update
process.
- Do not attempt to Power Off or restart the handheld while the
update is in progress.
- Do not enable “Show information when device is turned on”
feature during the update process. To disable this feature,
click “Owner” on the Today screen and uncheck the box at the
bottom of the page, then click the Notes tab at the bottom of
the page and uncheck “Show information when device is turned
on,” which is located at the bottom of the page.
- After applying a firmware (ROM) update, do not attempt to
restore a backup that was made before the ROM update was
installed.

3. IMPORTANT: Disable the Standby and Hibernation modes on the host PC.
If Standby or Hibernation mode is activated during the upgrade
process, a critical error may occur.

4. IMPORTANT: Plan enough time to complete the update process. The
total time to perform the firmware update is estimated to be as
follows:
- For USB connection - 10 minutes
- For Serial connection - 20 minutes

5. IMPORTANT: Do not interact with the handheld or remove it from
AC power or from the cradle/cable once the hourglass appears on
the handheld and the actual firmware update has started.

6. If an error message is displayed during the update process, follow
any available instructions to correct the condition and start the
update again.

7. The update process can be performed while connected to a host PC
either as a Guest or with an established partnership.

NOTE: This XIP firmware update does not change the ROM version. To confirm
that the XIP firmware update was successful, check the versions of the
individual components by clicking Start, Settings, System, and Asset Viewer
or by opening each individual application and checking the version number.
If the update was successful, applications will show version numbers,
as follows:

- Bluetooth Driver Version 1.4.1.60
- iPAQ Backup Software Version 1.1.0.6
- IPSM Version 3614.3212
- iTask Version 2.16
- iPAQ Image Viewer version 2.12b

Download:

http://rapidshare.com/files/89239190/iPAQ_H5100_Series_Firmware_Update_WM2003_v1.00.11_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H5400 Series ROM Update PPC2002 v1.11 (Official)

iPAQ H5400 Series ROM Update PPC2002 v1.11 (Official)

Requirements : iPAQ H5400 Series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ Pocket PC h5400 Series.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive. The file
downloaded is a self-extracting executable with a filename based
on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpacking the ROM Update files to a directory (NOTE: this directory
should not contain any file or folder from any previous ROM Upgrade).

3. Establish an Activesync connection between your iPAQ Pocket PC and host
PC through either the USB or Serial connection.

4. Execute the RUU.exe file in the directory created in step 2 above to
begin the upgrade process and follow the instructions displayed by the
ROM Upgrade Utility.

5. You may delete the self-extracting file downloaded in step 1 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Automatically place the iPAQ in flash mode.
- Update or restore a ROM image on your device.
- Require that you press Reset at the end which performs a Full reset
to complete the process.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Important: Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 20 minutes
*Serial - 90 minutes

4. Important: Do not interact with your device or remove it from AC power
or the cradle/cable once the status bar appears on the iPAQ and the actual
update has started.

5. If an error message is displayed during the process, follow any available
instructions to correct the condition and start the utility again.

6. The update process can be performed while connected to a host PC as a Guest
or with an established partnership.

Download:

http://rapidshare.com/files/89240739/iPAQ_H5400_Series_ROM_Update_PPC2002_v1.11_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H5500 Series Firmware Update WM2003 for ROM v1.10

iPAQ H5500 Series Firmware Update WM2003 for ROM v1.10

Requirements : iPAQ H5500 Series

Overview : This package contains an "execute in place" (XIP) .cab file that replaces the "Miscellaneous OEM" region of the ROM image for the listed handheld model. This is a permanent update to the flash ROM.

Installation Instructions :
1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Establish an Activesync connection between the iPAQ Pocket PC and
host PC using either a USB or Serial connection.

3. Execute the downloaded file and follow the on-screen instructions.

INSTALLATION NOTES:
1. If the Regional Settings are changed to any language other than the
default language of the handheld, the Firmware update will not
complete and the following error message will be generated:
"This update is language specific. Please visit the HP website to
verify that you have downloaded the correct update."

2. IMPORTANT: Please observe the following restrictions:
- Do not enable the handheld password feature during the update
process.
- Do not attempt to Power Off or restart the handheld while the
update is in progress.
- Do not enable the “Show information when device is turned on”
feature during the update process. To disable this feature,
click “Owner” on the Today screen and uncheck the box at the
bottom of the page, then click the Notes tab at the bottom of
the page and uncheck “Show information when device is turned
on,” which is located at the bottom of the page.
- After applying a firmware (ROM) update, do not attempt to
restore a backup that was made before the ROM update was
installed.

3. IMPORTANT: Disable the Standby and Hibernation modes on the host PC.
If Standby or Hibernation mode is activated during the upgrade
process, a critical error may occur.

4. IMPORTANT: Plan enough time to complete the update process. The
total time to perform the firmware update is estimated to be as
follows:
- For USB connection - 10 minutes
- For Serial connection - 20 minutes

5. IMPORTANT: Do not interact with the handheld or remove it from
AC power or from the cradle/cable once the hourglass appears on
the handheld and the actual firmware update has started.

6. If an error message is displayed during the update process, follow
any available instructions to correct the condition and start the
update again.

7. The update process can be performed while connected to a host PC
either as a Guest or with an established partnership.

NOTE: This XIP firmware update does not change the ROM version. To confirm
that the XIP firmware update was successful, check for a date of 6/22/04
on the mxip_MISC.ver file by pressing Start, Programs, File Explorer,
and Windows directory. The mxip_MISC.ver file can only be view with
the "View All Files" option selected. To set the "View All Files" option,
tab and hold on the blank area at the bottom of the File Explorer window.

Download:

http://rapidshare.com/files/89241343/iPAQ_H5500_Series_Firmware_Update_WM2003_for_ROM_v1.10_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H5500 Series ROM Update WM2003 v1.10 (Official)

iPAQ H5500 Series ROM Update WM2003 v1.10 (Official)

Requirements : iPAQ H5500 Series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ Pocket PC h5500 Series.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive. The file
downloaded is a self-extracting executable with a filename based
on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpacking the ROM Update files to a directory (NOTE: this directory
should not contain any file or folder from any previous ROM Upgrade).

3. Establish an Activesync connection between your iPAQ Pocket PC and host
PC through either the USB or Serial connection.

4. Execute the RUU.exe file in the directory created in step 2 above to
begin the upgrade process and follow the instructions displayed by the
ROM Upgrade Utility.

5. You may delete the self-extracting file downloaded in step 1 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Automatically place the iPAQ in flash mode.
- Update the ROM image on your device.
- Require that you press Reset at the end which performs a Full reset
to complete the process.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Important: Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 20 minutes
*Serial - 90 minutes

4. Important: Do not interact with your device or remove it from AC power
or the cradle/cable once the status bar appears on the iPAQ and the actual
update has started.

5. If an error message is displayed during the process, follow any available
instructions to correct the condition and start the utility again.

6. The update process can be performed while connected to a host PC as a Guest
or with an established partnership.

Download:

http://rapidshare.com/files/89243064/iPAQ_H5500_Series_ROM_Update_WM2003_v1.10_English.rar

Please Post Your Suggestions.
Read more!