iPAQ H4100 Series ROM Update WM2003 v1.10 (Official)

iPAQ H4100 Series ROM Update WM2003 v1.10 (Official)

Requirements : iPAQ H4100 Series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the listed handheld model.

Installation Instructions :
1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Execute the downloaded file and follow the on-screen instructions
to unpack the ROM Update files to a directory (NOTE: This
directory should not contain any file or folder from any previous
ROM Upgrade).

3. Establish an Activesync connection between the iPAQ Pocket PC and
host PC through either a USB or Serial connection.

4. Execute the RUU.exe file in the directory created in Step 2 to
begin the upgrade process. Follow the instructions displayed by
the ROM Upgrade Utility.

5. Delete the self-extracting file downloaded in Step 1, if desired.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query the device for current ROM image information.
- Validate that the new ROM image is compatible with the device.
- Automatically place the device in Flash mode.
- Update the ROM image on the device.
- Request that the device be reset when the installation is
complete.

2. IMPORTANT: Disable the Standby and Hibernation modes on the
host PC. If Standby or Hibernation mode are activated during the
upgrade process, a critical error may occur.

3. IMPORTANT: Plan enough time to complete the update process.
The total time required to perform a ROM backup and a ROM update
is estimated to be as follows:
* With USB connection - 20 minutes
* With serial connection - 90 minutes

4. IMPORTANT: Do not interact with the device or remove it from AC
power or the cradle/cable once the status bar appears on the
device and the actual update has started.

5. If an error message is displayed during the process, follow any
available instructions to correct the condition and start the
utility again.

6. The update process can be performed while connected to a host PC
either as a Guest or with an established partnership.

Download:

http://rapidshare.com/files/89236860/iPAQ_H4100_Series_ROM_Update_WM2003_v1.10_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H4300 Series ROM Update WM2003 v1.10 (Official)

iPAQ H4300 Series ROM Update WM2003 v1.10 (Official)

Requirements : iPAQ H4300 Series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the listed handheld model.

Installation Instructions :
1. Download the SoftPaq .EXE file to a directory on your hard drive.

2. Execute the downloaded file and follow the on-screen instructions
to unpack the ROM Update files to a directory (NOTE: This
directory should not contain any file or folder from any previous
ROM Upgrade).

3. Establish an Activesync connection between the iPAQ Pocket PC and
host PC through either a USB or Serial connection.

4. Execute the RUU.exe file in the directory created in Step 2 to
begin the upgrade process. Follow the instructions displayed by
the ROM Upgrade Utility.

5. Delete the self-extracting file downloaded in Step 1, if desired.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query the device for current ROM image information.
- Validate that the new ROM image is compatible with the device.
- Automatically place the device in Flash mode.
- Update the ROM image on the device.
- Request that the device be reset when the installation is
complete.

2. IMPORTANT: Disable the Standby and Hibernation modes on the
host PC. If Standby or Hibernation mode are activated during the
upgrade process, a critical error may occur.

3. IMPORTANT: Plan enough time to complete the update process.
The total time required to perform a ROM backup and a ROM update
is estimated to be as follows:
* With USB connection - 20 minutes
* With serial connection - 90 minutes

4. IMPORTANT: Do not interact with the device or remove it from AC
power or the cradle/cable once the status bar appears on the
device and the actual update has started.

5. If an error message is displayed during the process, follow any
available instructions to correct the condition and start the
utility again.

6. The update process can be performed while connected to a host PC
either as a Guest or with an established partnership.

Download:

http://rapidshare.com/files/89238634/iPAQ_H4300_Series_ROM_Update_WM2003_v1.10_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H3600 Series ROM Update PPC2002 v2.20 (Official)

iPAQ H3600 Series ROM Update PPC2002 v2.20 (Official)

Requirements : iPAQ H3600 series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ H3600 Series Pocket PC 2002.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive. The file
downloaded is a self-extracting executable with a filename based
on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpack the ROM Update files to a directory (NOTE: this directory
should not contain any files or folders from any previous ROM Upgrade)

3. Execute the UpgradeUt.exe file from within the directory that was
created from step 2 to begin the upgrade process and follow the
instructions displayed by the ROM Upgrade Utility.

4. You may delete the self-extracting file downloaded in step 1 if you wish.

5. After the installation is complete, you may delete
the directory created in step 2 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Update or restore the ROM image on your device.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 10 minutes
*Serial - 30 minutes

4. Important: Do not interact with your device or remove it from power
or the cradle/cable once the actual update has started.

5. The update process can be performed on a device connecting
to a host PC as an established partnership or as a guest.

6. When the ROM Update Utility is used on a host PC for the first time, the
Operating System may not recognize the iPAQ as a USB device after placing
the iPAQ in update mode. Ensure the iPAQ is recognized by waiting
for the host PC to properly find and install the USB driver again before
continueing the update process. (This is not to be confused with the
ActiveSync warning, "Device Not Recognized".)

Download:

http://rapidshare.com/files/89227783/iPAQ_H3600_Series_ROM_Update_PPC2002_v2.20_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H3700 Series ROM Update PPC2002 v2.20 (Official)

iPAQ H3700 Series ROM Update PPC2002 v2.20 (Official)

Requirements : iPAQ H3700 series

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ H3700 Series Pocket PC 2002.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive. The file
downloaded is a self-extracting executable with a filename based
on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpack the ROM Update files to a directory (NOTE: this directory
should not contain any files or folders from any previous ROM Upgrade)

3. Execute the UpgradeUt.exe file from within the directory that was
created from step 2 to begin the upgrade process and follow the
instructions displayed by the ROM Upgrade Utility.

4. You may delete the self-extracting file downloaded in step 1 if you wish.

5. After the installation is complete, you may delete
the directory created in step 2 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Update or restore the ROM image on your device.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 10 minutes
*Serial - 30 minutes

4. Important: Do not interact with your device or remove it from power
or the cradle/cable once the actual update has started.

5. The update process can be performed on a device connecting
to a host PC as an established partnership or as a guest.

6. When the ROM Update Utility is used on a host PC for the first time, the
Operating System may not recognize the iPAQ as a USB device after placing
the iPAQ in update mode. Ensure the iPAQ is recognized by waiting
for the host PC to properly find and install the USB driver again before
continueing the update process. (This is not to be confused with the
ActiveSync warning, "Device Not Recognized".)

Download:

http://rapidshare.com/files/89229110/iPAQ_H3700_Series_ROM_Update_PPC2002_v2.20_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H3815, H3830, H3835, H3845 and H3850 ROM Update PPC2002 v1.20 (Official)

iPAQ H3815, H3830, H3835, H3845 and H3850 ROM Update PPC2002 v1.20 (Official)

Requirements : iPAQ H3815, H3830, H3835, H3845 or H3850

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ H3815, H3830, H3835, H3845 and H3850 Pocket PC 2002.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive. The file
downloaded is a self-extracting executable with a filename based
on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpack the ROM Update files to a directory (NOTE: this directory
should not contain any files or folders from any previous ROM Upgrade)

3. Execute the UpgradeUt.exe file from within the directory that was
created from step 2 to begin the upgrade process and follow the
instructions displayed by the ROM Upgrade Utility.

4. You may delete the self-extracting file downloaded in step 1 if you wish.

5. After the installation is complete, you may delete
the directory created in step 2 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Update or restore the ROM image on your device.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 30 minutes
*Serial - 1 hour and 45 minutes

4. Important: Do not interact with your device or remove it from power
or the cradle/cable once the actual update has started.

5. The update process can be performed on a device connecting
to a host PC as an established partnership or as a guest.

6. When the ROM Update Utility is used on a host PC for the first time, the
Operating System may not recognize the iPAQ as a USB device after placing
the iPAQ in update mode. Ensure the iPAQ is recognized by waiting
for the host PC to properly find and install the USB driver again before
continueing the update process. (This is not to be confused with the
ActiveSync warning, "Device Not Recognized".)

Download:

http://rapidshare.com/files/89230339/iPAQ_H3815__H3830__H3835__H3845_and_H3850_ROM_Update_PPC2002_v1.20_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H3870 and H3875 ROM Update PPC2002 v2.20 (Official)

iPAQ H3870 and H3875 ROM Update PPC2002 v2.20 (Official)

Requirements : iPAQ H3870 or H3875

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ H3870 and H3875 Pocket PC 2002.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive (NOTE: this
directory should not contain any file or folder from any previous
ROM Upgrade). The file downloaded is a self-extracting executable
with a filename based on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpacking the ROM Update files to a directory.

3. Execute the UpgradeUt.exe file to begin the upgrade process and
follow the instructions displayed by the ROM Upgrade Utility.

4. You may delete the self-extracting file downloaded in step 1 if you wish.

5. After the installation is completed, you may delete
the directory created in step 2 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Update or restore the ROM image on your device.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 30 minutes
*Serial - 1 hour and 45 minutes

4. Important: Do not interact with your device or remove it from power
or the cradle/cable once the actual update has started.

5. The update process can be performed on a device connecting
to a host PC as an established partnership or as a guest.

6. When the ROM Update Utility is used on a host PC for the first time, the
Operating System may not recognize the iPAQ as a USB device after placing
the iPAQ in update mode. Ensure the iPAQ is recognized by waiting
for the host PC to properly find and install the USB driver again before
continueing the update process. (This is not to be confused with the
ActiveSync warning, "Device Not Recognized".)

Download:

http://rapidshare.com/files/89231876/iPAQ_H3870_and_H3875_ROM_Update_PPC2002_v2.20_English.rar

Please Post Your Suggestions.
Read more!

iPAQ H3970 and H3975 ROM Update PPC2002 v2.10

iPAQ H3970 and H3975 ROM Update PPC2002 v2.10

Requirements : iPAQ H3970 or H3975

Overview : This SoftPaq contains the ROM Update Utility (RUU) and ROM image for the iPAQ H3970 and H3975 Pocket PC 2002.

Installation Instructions :
1. Download the SoftPaq to a directory on your hard drive (NOTE: this
directory should not contain any file or folder from any previous
ROM Upgrade). The file downloaded is a self-extracting executable
with a filename based on the SoftPaq Number above.

2. Execute the downloaded file and follow the on-screen instructions
to unpacking the ROM Update files to a directory.

3. Execute the UpgradeUt.exe file to begin the upgrade process and
follow the instructions displayed by the ROM Upgrade Utility.

4. You may delete the self-extracting file downloaded in step 1 if you wish.

5. After the installation is completed, you may delete
the directory created in step 2 if you wish.

INSTALLATION NOTES:
1. During the update, the ROM Update Utility will:
- Query your device for current ROM image information.
- Validate that the new ROM image is compatible with your device.
- Allow you to back up your current ROM image.
- Update or restore the ROM image on your device.

2. Important: Disable the standby and hibernation modes on your
host PC. If standby or hibernation are activated during the
upgrade process, a critical error may occur.

3. Plan for enough time to start and complete the update process.
The total time to perform a ROM backup and a ROM update is
estimated to be as follows:
*USB - 30 minutes
*Serial - 1 hour and 45 minutes

4. Important: Do not interact with your device or remove it from power
or the cradle/cable once the actual update has started.

5. The update process can be performed on a device connecting
to a host PC as an established partnership or as a guest.

6. When the ROM Update Utility is used on a host PC for the first time, the
Operating System may not recognize the iPAQ as a USB device after placing
the iPAQ in update mode. Ensure the iPAQ is recognized by waiting
for the host PC to properly find and install the USB driver again before
continueing the update process. (This is not to be confused with the
ActiveSync warning, "Device Not Recognized".)

Download:

http://rapidshare.com/files/89234860/iPAQ_H3970_and_H3975_ROM_Update_PPC2002_v2.10_English.rar

Please Post Your Suggestions.
Read more!

Pocket PC 2003 ROM Upgrade for iPAQ H3900 Series

Pocket PC 2003 ROM Upgrade for iPAQ H3900 Series

Requirements : iPAQ H39xx

Overview : Official English upgrade for iPaq H3900 series

Installation Instructions :
Run the program and follow instructions.

Download:

Run the program and follow instructions.
http://rapidshare.com/files/31872146/WWE_H3900_BTa.rar

Alternative version (works on H3950):
http://www.megaupload.com/?d=MZ48VQ9E

Please Post Your Suggestions.
Read more!

iPAQ 38xx series Windows Mobile 2003

iPAQ 38xx series Windows Mobile 2003

Requirements : iPAQ 38xx Series

Overview : Upgrades windows mobile 2002 to 2003. This software is intended for iPAQ 3870. the 3870 is only different in that the other 38xx series did not have a bluetooth device. I have successfully installed this on a non-bluetooth 3850 and it works completely fine, all it does is have a little icon on the bottom-right hand corner with a bluetooth symbol with an smaller X over it, meaning bluetooth is disabled.

Installation Instructions :
Please follow the instructions EXACTLY, and if you are confused, then just dont do it man.
You will need these 2 files:
the ROM: http://blog.crowe.co.nz/attachments/nk.nb0.zip
UltraEdit: http://rapidshare.com/files/4986784/UltraEdit-32_11.00b.rar

Installation Instructions:
1) extract the contents of "nk.nb0.zip" to your desktop (in its own folder)
2) re-name the file "nk.nb0.bak" to "nk.nb0"
3) Install ultraEdit, and run it.
4) open the file nk.nb0
5) press CTRL+G to go to a specific area in the file and type "0x01ff000a" (without quotation marks!) and press enter.
6) You will see a few numbers/letters on the right hand side (e.g. 4.G.1.C.D.W.3.3.W.0.H.G). This is a SERIAL NUMBER. change the serial number to YOUR serial number located on the back of your iPAQ.
7) you must do this again in another area, so press CTRL+G again, and type "0x01ff0e0a" (without quotation marks) and press enter.
8 ) do the same as step 6.
9) Save the file and exit UltraEdit.
That is the hard bit over. Now to install the fookin thing.
1) First of all you MUST close ActiveSync, so go ahead and press CTRL+ALT+DEL, click the processes tab, and end the program WCESCOMM.EXE by clicking once on the file name, and clicking the "End Task" button.
2) You need to put your iPAQ in "USB Update Mode". So, Hold softkey 2, 4 and the power button together, and while holding them, press the tiny reset button that you normall press to do a soft-reset, and hold them there until your screen says "REMOTE USB UPDATE", then let go of the buttons. (see picture below)
Image
3) put your iPAQ into the cradle, windows will find a synchronisation device.
4) run the file "HOST11.EXE" located in the folder with the file "nk.nb0"
5) it should start updating, will take around 5 minutes.
6) Once updated, you need to do a hard reset by pressing buttons 1 and 4, and pressing the soft-reset button, and holding them ALL for around 10-20 seconds.
7) turn on your iPAQ, first-time power-on will take a couple of minutes maybe so dont worry.
Thats it! updated to Windows Mobile 2003.



Edit: To get rid of the bluetooth option (if you dont have bluetooth) just go to "\windows\startup" on your PPC and delete the file "BTTrayCE.lnk" (or move it somewhere else if you like ) and do a soft reset (switch-off wont work).

Warning: Please do not do this if you do not understand, feel free to ask any questions, but remember, ALWAYS do a backup, and that the machine belongs to YOU, not me.

Download:

the ROM: http://blog.crowe.co.nz/attachments/nk.nb0.zip
UltraEdit: http://rapidshare.com/files/4986784/UltraEdit-32_11.00b.rar

Please Post Your Suggestions.
Read more!

Ipaq h3800 series WM 2003

Ipaq h3800 series WM 2003

Requirements : iPaq H3800

Overview : Official upgrade for iPaq H3800 series.

Installation Instructions :
Extract Download host11.exe and firmware file on desktop. Disable USB in ActiveSync.Put iPAq in flash mode: for H38xx, press button2+button4+power+reset until you get "Remote USB Update" message displayed on the screen Connect the iPAq to desktop via USB cradle Start host11.exe.After flashing process perform hardreset,press Button1+Button4,Power and reset Button

Download:

http://qshare.com/get/156635/Ipaq_3850_Pocketpc_2003_Rom_Update.zip.html

Please Post Your Suggestions.
Read more!